In a bathroom, the light at the mirror matters more than everything else combined: it's where you shave, put on makeup and check your skin. This plan starts there, then fills in the rest of a typical family bathroom with numbers from our calculators.
Layer 1: the mirror light
For a 36″ mirror, the vanity light calculator suggests a light 25–29″ wide, typically a 3- or 4-light bar, mounted with its bottom about 3″ above the mirror. With the mirror top at 72″, that puts the electrical box at about 79″ above the floor.
Sconces on both sides of the mirror light faces even better, but only when they're close together. Here they'd end up 49″ apart, too far to light the middle of your face evenly, so a light above the mirror is the better choice. With a mirror under about 27″ wide, side sconces would work well.
Choose a fixture whose glass shades send light forward toward you, not just down at the sink, and bulbs with CRI 90+ so skin looks true.
Layer 2: ceiling and shower lights
The recessed lighting calculator lays out a 3 × 2 grid for this room. In a bathroom this size, we'd use four lights placed around the fixtures instead:
- One in front of the vanity, about 3 ft out from the wall, so it lights the room without casting shadows on your face at the mirror.
- Two over the open floor by the toilet and the door.
- One over the tub, wet-rated because it's inside the shower area.
The others need to be at least damp-rated. Never hang a pendant or chandelier over the tub on an 8 ft ceiling: the US electrical code (NEC 410.10(D)) keeps hanging fixtures out of the space 3 ft around and 8 ft above the tub rim.
Is it bright enough?
Four 650-lumen lights plus a vanity light of about 1,800–2,000 lumens gives roughly 4,400–4,600 lumens, or 55–58 per square foot. Retailer guides recommend 70–80 for bathrooms, while lists based on the Illuminating Engineering Society give 20–50. We land between the two, with the strongest light at the mirror, where you need it. Our lumens calculator explains the difference.
Layer 3: night light
A dim LED strip under the vanity's toe-kick, on a motion sensor or its own switch, lights the floor at night without waking you up. It also makes the vanity look like it's floating, which is a nice side effect.
Color temperature and CRI
Use 2700–3000K and CRI 90+ for every light in the room, especially the mirror light. Higher CRI matters more here than anywhere else in the house. See what is CRI.
Shopping list
| Fixture | How many | Size | Placement | Light |
|---|---|---|---|---|
| Vanity light, damp-rated | 1 | 25–29″ wide | Box center at 79″, bottom about 3″ above mirror | About 1,800–2,000 lm, 2700–3000K, CRI 90+ |
| Recessed lights, damp-rated | 3 | 4″ | In front of the vanity and over the open floor | About 650 lm each |
| Recessed light, wet-rated | 1 | 4″ | Over the tub and shower | About 650 lm |
| Toe-kick LED strip | 1 | Length of the vanity | Under the vanity | Low, warm |
Switching
Put the vanity light on a dimmer of its own, so you can have bright light for shaving and makeup and soft light for a bath. Ceiling lights go on a second switch, and the night strip on a motion sensor or a third switch. If the ceiling has an exhaust fan with a light, wire the fan separately so it can run after you switch the lights off.
Mistakes to avoid
- A single recessed light directly over the sink, which casts dark shadows under your eyes and chin.
- A vanity light wider than the mirror.
- Ordinary indoor fixtures near the shower. Check the damp or wet rating on every bathroom fixture.
- Cheap CRI 80 bulbs at the mirror, which make skin look sallow.