When to call an electrician first
If lights flicker on circuits without dimmers, if many lights around the house flicker at once, or if a switch or outlet feels warm, buzzes loudly or smells of burning, stop and call a licensed electrician. Those are signs of a loose connection or a wiring problem, not a bulb problem. Always turn off the breaker before touching a switch or fixture.
Why LEDs and dimmers clash
Most wall dimmers work by chopping off part of each cycle of the electricity. Incandescent bulbs, which are just a hot wire, don't mind. LED bulbs contain a small electronic driver that has to interpret that chopped power and turn it into a steady current for the LEDs. When the dimmer and the driver don't understand each other, you get flicker, buzzing, light that drops out at the bottom of the range, or bulbs that glow when they should be off.
There are two main dimmer types. Leading-edge dimmers (also called TRIAC or incandescent dimmers) are the older, common kind. Trailing-edge dimmers (also called ELV or reverse-phase) cut the other end of the cycle, and many LED drivers work more smoothly with them. Bulb packaging or spec sheets often say which type they're designed for.
Find your symptom
| What you see | Likely cause | Fix |
|---|---|---|
| Flicker or buzz at every setting | Bulbs not dimmable, or dimmer not made for LEDs | Use bulbs marked "dimmable" and an LED-rated dimmer |
| Flicker or cuts out only near the bottom | Dimmer's low end set too low for the bulbs | Raise the low-end trim on the dimmer |
| Flicker with only one or two bulbs on the dimmer | Load below the dimmer's minimum | Add bulbs, or use a dimmer with a lower minimum load |
| Bulbs glow or flash when switched off | Small current leaking through the dimmer or smart switch | Use a dimmer wired with a neutral, or the maker's bypass device |
| Lights jump from off to fairly bright | Dimmer range doesn't match the bulbs | Adjust the trim, or use a compatible pairing |
| One bulb flickers, the rest are fine | Loose or failing bulb, or a different model | Reseat it, then replace it with the same model as the others |
| Flicker only visible on phone video | Fast flicker from the bulb's driver | Usually harmless. Choose bulbs sold as "flicker-free" if it bothers you. |
Fixing it, step by step
- Check the bulbs say "dimmable". Non-dimmable LEDs flicker and fail early on a dimmer, whatever the dimmer.
- Use the same bulb model on each dimmer. Different brands have different drivers, and one can upset the others.
- Check the dimmer is LED-rated. Older dimmers were designed for hundreds of watts of incandescent load. A few LEDs drawing about 10 W each may fall below their minimum. LED-rated dimmers list a separate, lower LED rating, often a quarter of their incandescent rating. Stay under it.
- Check compatibility. Bulb and dimmer makers publish lists of pairings they've tested. Products that meet the NEMA SSL 7A standard are designed to work together.
- Adjust the low-end trim. Many LED dimmers have a small dial or a setting mode that raises the lowest level. Set it just above the point where flicker starts.
- For glowing when off, choose a dimmer that uses a neutral wire, which many smart dimmers need anyway. Some makers sell a small bypass device for the fixture.
Most people can change a bulb themselves. Replacing a dimmer means working on household wiring, so unless you're comfortable doing that safely and it's allowed where you live, have an electrician do it.
Buying lights that dim well
- Look for "dimmable" and, ideally, a range like "dims to 5%" or "dims to 1%".
- Check the bulb maker's compatibility list before buying a dimmer, or the dimmer maker's list before buying bulbs.
- For recessed lights, choose fixtures and a dimmer from lists that name each other. The recessed lighting calculator helps you work out how many you need.
- Consider "dim-to-warm" bulbs for living spaces. They turn warmer as they dim, like incandescent bulbs did (see color temperature by room).