Calculator

Chain Length Calculator

You've bought the light; now it has to hang at the right height. Enter your ceiling and the fixture's measurements to get the chain, rod or cord length, and how much to take off what came in the box.

Quick answer: chain length = ceiling height − canopy − fixture height − the height you want the bottom at. For a 24″ chandelier over a 30″ table with a 9 ft ceiling, that's 12–18″ (30–46 cm) of chain.

Embed this calculator on your site

Free for blogs, designers, electricians and retailers. Paste this code where you want the calculator to appear. It resizes itself to fit.

The formula

Chain = ceiling height − canopy − fixture height − bottom height

Example: a 9 ft (108″) ceiling, a 3″ canopy, a 24″ chandelier, and its bottom 33″ above a 30″ table (63″ from the floor). 108 − 3 − 24 − 63 = 18″ of chain.

The bottom height depends on what's underneath. Over a table or island it's 30–36″ above the surface with an 8 ft ceiling, plus about 3″ for each extra foot. Over open floor it's at least 7 ft. The chandelier height guide covers every case.

Chain needed for common ceilings

For a 24″ (61 cm) tall fixture and a 3″ (8 cm) canopy
CeilingOver a 30″ tableOver a 36″ island
8 ft (2.44 m)3–9″ (8–23 cm)0–3″ (0–8 cm)
9 ft (2.74 m)12–18″ (30–46 cm)6–12″ (15–30 cm)
10 ft (3.05 m)21–27″ (53–69 cm)15–21″ (38–53 cm)
12 ft (3.66 m)39–45″ (99–114 cm)33–39″ (84–99 cm)

For a taller or shorter fixture, subtract or add the difference. A 30″ fixture needs 6″ less chain than the table shows.

Measuring the fixture

Product listings usually give two heights. Fixture height (or body height) is the light itself, from the top loop to the lowest crystal or finial. Overall or maximum height includes all the chain or rods at full length. Use the fixture height in the formula. If the listing only gives overall height, measure the fixture yourself before you hang it.

Chain, rods or cord

Chain

Chain is the easiest to adjust. Open links with two pairs of pliers, take them off at the top near the canopy, and keep the spares in case you move house. On twisted or patterned chain, remove links in pairs so the chain still hangs straight. Weave the wire back through the remaining links.

Rods

Rods (also called stems or downrods) come in fixed lengths, often 6″ or 12″, so you can only adjust in those steps. The calculator picks the whole number of rods that lands within the range. If none does, it tells you where the bottom will end up with the closest choice. Makers often sell extra or shorter rods in the same finish.

Cord or cable

Most pendants with a fabric cord or steel cable adjust at the canopy: you slide the cord through a grip and coil the extra inside. Don't cut a cord unless the instructions say you can, because some contain the wiring in a way that can't be safely shortened at home.

Safety

Common questions

How much chain do I need for a chandelier with a 10 ft ceiling?

For a 24″ chandelier over a dining table, about 21–27″. For a fixture over open floor, enough to keep its bottom at least 7 ft up. The calculator works it out for your fixture.

What if the chain that came with it is too short?

Most makers sell extension chain in the same finish. Measure the link size and finish, or order through the maker so they match.

Can I use a downrod instead of a chain?

Only if the fixture is designed for it. Rods need a matching canopy and coupling, so check with the maker before switching.

Should the chain be the same finish as the fixture?

Usually, yes. Some designers cover the chain with a fabric sleeve instead, which hides both the chain and the wire.